ASTM D is a standard test anaerobic biodegradation test method for determining anaerobic biodegradation of plastic materials under high-solids. ASTM D Standard Test Method. D Standard Test Method for Determining Anaerobic Biodegradation of Plastic Materials Under. High-Solids. ASTM D Significance and Use. Biodegradation of a plastic within a high- solids anaerobic digestion unit is an important phenomenon because it will affect .
|Published (Last):||18 September 2008|
|PDF File Size:||3.99 Mb|
|ePub File Size:||5.37 Mb|
|Price:||Free* [*Free Regsitration Required]|
These gasses are measured daily and the results are carefully recorded.
BioPro Global – ASTM D
Active view current version of standard. Reports shall clearly state the percentage of net gaseous carbon generation for both the test and reference samples at the completion of the test. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
Note asfm test method is equivalent to ISO Furthermore, results shall not be extrapolated past the actual duration of the test. Furthermore, asm shall not be extrapolated past the actual duration of the test.
Reports shall clearly state the percentage of net gaseous carbon generation for both the test and reference samples at the completion of the test.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard.
As these bacteria begin to utilize the carbon in the test samples, they produce carbonaceous gasses such as CO2 and CH4. The test is allowed to run for as long as desired.
However, it is expected to resemble the environment of a high-solids anaerobic-digestion process operated under optimum conditions.
Then, the anaerobic bacteria begin to multiply and colonize in the vessel. Specific hazards are given in Section 8. If the positive control which contains cellulose continues to exhibit biodegradation then the test is considered valid and the inoculum considered alive. The testing process includes: Historical Version s – view previous astn of standard.
ASTM D5511 – Anaerobic Biodegradation
The test materials are exposed to a methanogenic inoculum derived from anaerobic digesters operating only on pretreated household waste. Placing the samples in incubation vessels after the inoculum is prepared. Depleting the oxygen in the incubation vessels after an initial burst of aerobic activity.
Link to Active This link will always route to asttm current Active version of wstm standard. This procedure has been developed to permit the determination of the rate and degree of anaerobic biodegradability of plastic products when placed in a high-solids anaerobic digester for the production of digestate from municipal solid waste. The procedure is intended to create a standard laboratory environment that will permit a rapid and reproducible determination of the anaerobic biodegradability astk high-solids digestion conditions.
Work Item s – proposed revisions of this standard.
Asym Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. Biodegradation of plastics could allow for the safe disposal of these plastics through aerobic and anaerobic solid-waste-treatment plants. Link to Active This link will always route to the current Active version of the standard.
This inoculum contains methanogenic bacteria that are also found in landfills. This test method is designed to be applicable to all plastic materials that are not inhibitory to the microorganisms present in f5511 digesters operating on household waste.
Specific hazards are given in Section 8. This test method also resembles other anaerobic conditions where the gas generated is recovered and biogas production is actively promoted by inoculation for example, codeposition of anaerobic sewage sludge, anaerobic leachate recirculationmoisture control for example, leachate recirculationand temperature control for example, short-term injection of oxygen, heating of recirculated leachate 5, 6, 7.
When the test is run to satisfaction, v5511 carbon and methane gas readings are recorded and the incubation vessels are emptied and the samples are cleaned and aastm.
Placing the sample materials in an inoculum derived from anaerobic digesters operating on household waste. Work Item s – proposed revisions of this standard. Three vessels d55111 used for each sample, and one negative control and one positive control are prepared as well.